• úvod
  • témata
  • události
  • tržiště
  • diskuze
  • nástěnka
  • přihlásit
    registrace
    ztracené heslo?
    PEEPMAN - truck & bus
    FREEK303
    FREEK303 --- ---
    HEINZZ: checked it out and it looks like its all working....
    tested it with a running engine and all good, I hope there was some cable in the way who blocked the cable so not fully closing of the system.
    this evening we will test in on the road, let's hope it's fixed!
    HEINZZ
    HEINZZ --- ---
    FREEK303: did you look at the valve when disconnected? does it really move when you pull the wire?
    or maybe it's simply too hot and the air is not heated by the heater core... = )
    FREEK303
    FREEK303 --- ---
    KCE: So fucking fuck all working good all wires okay and all conected.... so tomorrow i will stop hot water intake:(
    FREEK303
    FREEK303 --- ---
    KCE: Let you know tomorrow if i fucked up :)
    KCE
    KCE --- ---
    also had to disconect couple of cables, dont forget the order to reconect after, good luck ;)
    KCE
    KCE --- ---
    FREEK303: yea, its under the middle part, start with poping out plastic panels around vent switch on left and ac switch on right, under there are some philips head screws, then some screws on do bottom side above motor/gearbox place, than the upper plastic-shelf... i'll find out ;)
    at the end comes the central part where the 4 switches (temperature,where to blow,windows,in/out air) and there are the control cables...
    whatch out for not to break the switches, there's the ligthning parts of plastic under the panels
    FREEK303
    FREEK303 --- ---
    KCE: Cheers i will try tomorrow:)
    KCE
    KCE --- ---
    FREEK303: beat it with ac! :D
    now seriously, maybe only the switch/control cables. have to put of the dash board, nothing complicated..max 1 hour for 1st time
    FREEK303
    FREEK303 --- ---
    hello, i have a new problem with my man 8.163 its blowing hot air even when i switch to max cold air(max pain in the ars in the summer). anyone who could help me? cheers!!!
    KCE
    KCE --- ---
    Nákladní vozidla valníky MAN 630 L2 AE, 2 STÜCKS na prodej, valník v Česku, koupit nákladní vozidlo valník, XQ14363
    https://autoline.cz/-/nakladni-vozidla-valniky/MAN-630-L2-AE-2-STuCKS--18020219271128972400
    KCE
    KCE --- ---
    taky tu mam navic fungl novy predni kotouce.. 1500 za oba je vic nez fer cena:)
    Nove brzdove kotouce predni MAN L2000 8.163 SLEVA - Karlovy Vary
    https://auto.bazos.cz/inzerat/95202187/Nove-brzdove-kotouce-predni-MAN-L2000-8163-SLEVA.php
    KCE
    KCE --- ---
    nepotrebujete nekdo diferak? mam tu jeden navic... pro zdejsi sleva ;)
    Diferencial MAN - Karlovy Vary
    https://auto.bazos.cz/inzerat/94435457/Diferencial-MAN.php
    PEEP
    PEEP --- ---
    a kdyz uz jsme u toho - shanim nejakou knowledge base na ZF prevodovky, nemate najky tip?

    pripadne muzu nabidnout betriebsanleitung pro M90 radu vcetne typu instalovanych motoru/prevodovek
    KCE
    KCE --- ---
    _A5_: mrkni na ten manWis, budes spokojenej;)
    a drzak to je o tom zadna:)
    _A5_
    _A5_ --- ---
    Skoda, ze na MAN l2000 nejsou anglicky manualy (Haynes) jako na sprintera. Diky tomu manualu jsem si mohl i ja, jakozto lama, leccos opravit sam. Ted je to spis pokus-omyl. Ale nastesti je MAN zatim vetsi drzak nez MB, takze nic moc resit nemusim.
    KCE
    KCE --- ---
    PEEP: no vida, me nenapadlo stahnout man wis :P

    nic konkretniho nepotrebuju, spis tak mit po ruce nakej manual kam muzu obcas kouknout na utahovaci momenty atd.. (coz doted sem louskal z toho ruskyho;)

    jo a kdyby nekdo potreboval cisla dilu tak jam mam zas komplet funkcni MANTis...
    Kliknutím sem můžete změnit nastavení reklam